Honda CR-V Lug Nut Torque Spec and Tightening Order
Honda CR-V lug nut torque is 80 lb-ft (108 N·m) for common factory wheels. See Honda's tightening order, multiple-pass method, and safety checks.
Honda specifies 80 lb-ft (108 N·m) for common CR-V original-equipment wheel nuts. Tighten in the illustrated crisscross order, go around two to three times, and verify the exact model-year manual.
The short answer for the most common Honda CR-V application is 80 lb-ft (108 N·m), but wheel torque is a safety specification—not a value to guess from memory. Model year, platform, stud size, factory wheel design, and an aftermarket wheel manufacturer's instructions can change the required value. This guide therefore starts with the verified application table and then explains how to produce an accurate clamping load instead of merely making the wrench click.
Correct torque keeps the wheel seated evenly against the hub. Too little clamping force can let the wheel move and loosen the fasteners. Too much can stretch studs, damage the nut seat, distort a brake rotor, or make roadside removal impossible. Read the scope note, identify the vehicle and wheel, clean the mating surfaces, and use a calibrated torque wrench for the final passes.
Interactive Honda CR-V lug-tightening diagram
STAR PATTERN
Branded downloads includedPNG and PDF exports carry the TorqueSheet logo, torquesheet.com, source-page URL, and republishing attribution request. The PDF source link is clickable.
Select each position to follow a five-lug star pattern. Six-lug wheels use the same opposite-side principle; follow the pattern in the exact owner manual.
Honda Crv Lug Nut Torque Spec
| APPLICATION / ITEM | SPECIFICATION | NOTES |
|---|---|---|
| CR-V factory wheel | 80 lb-ft (108 N·m) | Honda owner-manual specification |
| Pattern | Crisscross/star | Two to three passes |
| Mounting face | Wipe clean | Wheel must seat metal-to-metal |
| Final tightening | Torque wrench | Do not use foot or pipe leverage |
Honda warns against extra leverage from a pipe or foot and instructs technicians to wipe the mounting surfaces before installation.
How to read the CR-V torque table
Start with model year and platform rather than wheel diameter. Factory 17-, 18-, and 20-inch wheels can share a value when they use the same stud and seat design, while two trucks sold in the same calendar year can differ because one is an outgoing platform. Honda's 80 lb-ft figure applies across many CR-V generations with original-equipment wheels, but always verify the exact manual.
The figures in this guide assume original-equipment-style fasteners and clean, dry threads unless the cited manufacturer says otherwise. If an aftermarket wheel, spacer, conversion stud, locking nut, or repair kit supplies a different instruction, that component-specific document controls. Record the final value on the work order so the next technician does not have to infer it.
Common mistakes that produce an unsafe wheel installation
AWD hardware does not justify transferring torque values from axle or suspension fasteners to the wheel nuts. Treat an unfamiliar nut seat, stud, spacer, or wheel as a reason to stop and identify the hardware before tightening.
- Using a value from a different generation, heavy-duty model, or aftermarket wheel.
- Applying oil or anti-seize to a specification written for dry threads.
- Cross-threading with an impact gun instead of starting every nut by hand.
- Tightening clockwise around the circle instead of using an opposite-side pattern.
- Letting the full vehicle weight trap a wheel that is not yet centered on the hub.
- Skipping the confirmation pass and the post-service recheck.
Honda CR-V specifications can change by model year, engine, platform, wheel, and installed component. Confirm the VIN or engine identity, part numbers, fastener condition, and the current manufacturer instructions before service.
Procedures used with this specification
These steps are the same for every vehicle in this family, so they are documented once rather than repeated on each page. The values above remain specific to this Honda CR-V.
Honda CR-V Lug Nut Torque Spec and Tightening Order FAQs
What is the honda crv lug nut torque spec?+
Honda specifies 80 lb-ft (108 N·m) for common CR-V original-equipment wheel nuts. Tighten in the illustrated crisscross order, go around two to three times, and verify the exact model-year manual. Use the application table because the broad search phrase can cover more than one platform or model year.
Technical sources
TorqueSheet favors engine- and component-specific manufacturer instructions over unsourced universal values.
12025 Honda CR-V Owner's Manual — flat-tire procedurePrimary Honda procedure specifying 80 lb-ft and multiple passes through the tightening order.↗