P2135 means redundant throttle-position signals no longer agree within their calibrated relationship. Connector or harness faults, shared five-volt reference problems, throttle electronics, binding/contamination and calibration are possible. Unlike certain older GM cars, the commonly cited sensor-cover bulletin does not list the Traverse; diagnose this vehicle with its own year/engine Service Information.
Match the symptom
Select the closest observation. The result changes the first test; it does not name a part to replace.
Save codes and avoid demanding acceleration.
When the P2135 repair is actually complete
The repair is complete when the original operating condition is reproduced safely, the monitored values behave normally and no pending P2135 or related fault returns. Turning off the lamp or clearing memory alone proves nothing.
Recheck for oil, fuel, vapor, coolant or boost leaks and inspect anything moved during testing. If the original condition cannot be reproduced because weather, fuel level or temperature changed, document that limitation and continue monitoring rather than claiming certainty.
If the code returns, compare the new freeze frame with the first. The same pattern suggests an incomplete root-cause repair; a different load, temperature or companion-code pattern may reveal a second fault.
What can set P2135—and how to separate it
The order below is evidence-driven, not a universal probability ranking. Vehicle year, repair history, companion codes and the operating condition in freeze frame change where diagnosis should begin.
| Possible cause | Evidence that supports it | First useful test |
|---|---|---|
| Throttle-position sensor disagreement | TP1/TP2 relationship breaks | Graph both signals through controlled sweep |
| Connector/terminal or harness fault | Dropout with movement/heat | Terminal, pin-fit and circuit load tests |
| Shared five-volt reference/ground fault | Multiple sensor codes | Isolate shared branches |
| Throttle contamination/binding | Plate movement abnormal and inspection supports it | Follow approved cleaning/inspection method |
| Calibration or older serviceable cover condition | Matched bulletin/application | Follow VIN-specific GM procedure |
Correlation must be captured when it fails
Graph TP sensor 1 and 2 through a controlled sweep and during the original temperature/vibration condition. Two normal readings after a key cycle do not disprove an intermittent terminal dropout.
Keep fingers and tools out of an energized electronic throttle. After a proven repair, perform VIN-specific setup/relearn and confirm smooth agreement without pending Reduced Power codes.
What an owner can check—and where to stop
With the engine cold, an owner can inspect oil and coolant levels, the air-filter housing, intake and charge pipes, battery terminals, accessible grounds, EVAP hoses and connectors disturbed during recent work. Photograph the original condition and avoid unplugging several components at once.
Professional equipment is appropriate for regulated EVAP smoke, bidirectional purge/vent or throttle commands, charge-air pressure testing, oscilloscope cam/crank correlation, mechanical oil-pressure measurement, fuel-pressure work, compression/leak-down and catalyst testing. Turbo plumbing can contain hot oil residue and pressurized air; fuel vapor and moving throttle plates add separate hazards.
Ask the repairer which test failed, under what conditions and which RPO-specific procedure was used. A line reading only ‘code present—replace component’ does not distinguish the component from its wiring, plumbing, calibration or the upstream fault that damaged it.
Repair verification
Clear P2135 only after saving the original evidence and repairing a proven cause. Reinspect every disturbed seal, clamp, connector and fluid level, then monitor the relevant data at idle before attempting a road test.
Repeat the safe portion of the freeze-frame condition. A turbo moisture fault may require climate-specific reasoning; an EVAP monitor needs the correct fuel level and soak; a catalyst monitor will not be meaningful while misfire or fuel control remains abnormal.
Check pending codes after the drive and allow readiness to progress without repeated resets. Permanent codes disappear after the vehicle completes enough passing monitor operation, not because the battery was disconnected. Keep before-and-after reports.
Save these scan-data clues
Freeze frame is a snapshot of conditions when the PCM matured the fault. It can distinguish an idle-only problem from a load, cold-start or monitor-completion problem. Clearing first throws that context away.
- Confirmed, pending and permanent codes
- RPM, load, coolant and intake temperature
- Vehicle speed and time since start
- Battery voltage and relevant five-volt reference
- Companion codes and recent repair history
- Relevant commanded-versus-actual PIDs
- TP sensor 1 and 2 voltage/percent
- Commanded and actual throttle angle
- Accelerator-pedal PIDs and five-volt companion codes
A practical diagnostic workflow
- 01Save Reduced Power evidence
Record current/history status before key cycling.
- 02Identify year and engine
Determine whether the older bulletin applies.
- 03Graph both TP signals
Look for disagreement/dropout, not just final values.
- 04Inspect and load-test circuits
Check pin fit, reference, ground and signal integrity.
- 05Inspect throttle safely
Follow SI; keep fingers out of an energized electronic throttle.
- 06Complete setup and road verification
Perform required relearn/programming and confirm smooth correlation.
Do not automatically replace the throttle body and do not apply a Malibu/Equinox sensor-cover bulletin to a Traverse. Capture both TP signals and test reference, ground, terminals and harness first.
Why the model year changes the test
Traverse diagnostics divide into the first-generation 3.6L LLT/LFX, the second-generation 3.6L LFY, a limited 2.0L turbo application, and the newer 2.5L turbo generation. Bank layout, fuel pressure, timing hardware, air plumbing and GM bulletins change with engine RPO and build date. Confirm the VIN and emissions label before choosing a test.
- First- and second-generation V6 throttle bodies, connectors and setup procedures differ from the newer turbo engine.
- Multiple five-volt-reference or accelerator-pedal codes raise a shared circuit fault above an isolated throttle assembly.
- No unrelated GM-model sensor-cover repair is presented as Traverse guidance.
P2135 FAQ
Can I drive with P2135?+
Avoid normal driving because reduced-power response can be unpredictable.
Does it mean a bad throttle body?+
No. Wiring, terminals, reference voltage and calibration can cause it.
Why are there two sensors?+
The ECM compares redundant signals to detect unsafe disagreement.
Can cleaning fix it?+
Only when approved inspection proves contamination/binding; cleaning cannot repair electronics.
Can a battery reset fix it?+
It may clear symptoms temporarily but does not repair the cause.
Does the 2007–2009 bulletin apply to newer cars?+
No. It is limited to listed years and V6 RPOs.
Is a relearn required?+
Follow VIN-specific SI after repair; requirements vary.
What confirms repair?+
Smooth correlated TP signals and no pending fault through the original condition.
Ford diagnostic references
These documents explain Ford monitor operation. Exact pinpoint tests, connector views and specifications must be selected for the truck's VIN and model year in current service information.
01Chevrolet manuals and guidesOfficial GM model-year and VIN manual lookup; use VIN-correct Traverse procedures and specifications↗