2018 Toyota Camry 2.5 Oil Capacity
2018 Toyota Camry 2.5 Oil Capacity: 4.8 US qt with filter, application boundaries, refill procedure, dipstick check and official manual lookup.
Toyota lists 4.8 US qt (4.5 L) with a new filter for the gasoline 2018 Camry 2.5L A25A-FKS.
Toyota lists 4.8 US qt (4.5 L) with a new filter for the gasoline 2018 Camry 2.5L A25A-FKS. That number is a refill starting point for the identified engine, not permission to pour the entire amount without checking. Oil can remain in galleries, coolers, a tilted pan, or an old filter, and aftermarket pans can change total volume. The safest method is to verify the engine code and model year, use the correct viscosity and approval, refill slightly below capacity, circulate the oil, wait, and finish by the dipstick.
This guide separates similarly named engines and model generations because capacity errors commonly come from a search result that omits the year or engine code. The table also distinguishes “with filter” from “without filter.” During a normal oil change, replace the filter and use the with-filter figure, then confirm the final level on level ground under the conditions specified by the owner manual.
Interactive Toyota 2018 Camry 2.5L oil-service workflow
Branded downloads includedPNG and PDF exports carry the TorqueSheet logo, torquesheet.com, source-page URL, and republishing attribution request. The PDF source link is clickable.
Follow the workflow from vehicle identification through final dipstick verification. Published capacities are starting quantities, not a substitute for the level check.
2018 Toyota Camry 2.5 Oil Capacity
| APPLICATION / ITEM | SPECIFICATION | NOTES |
|---|---|---|
| Oil and filter change | 4.8 US qt | 4.5 L; with filter |
| Final level | Verify after drain-back | Level ground and correct procedure |
Toyota describes the figure as a drain-and-refill reference. Add below 4.8 qt initially, run the engine long enough to fill the filter, inspect the drain plug and filter, switch off, wait more than five minutes on level ground and bring the dipstick level into range. The gasoline A25A-FKS page specifies SAE 0W-16; if 0W-20 is used only because 0W-16 is unavailable, Toyota directs replacement with 0W-16 at the next change.
Oil-capacity chart for 2018 Camry 2.5L
Use the chart as an application lookup. Applies to the conventional gasoline 2018 Camry 2.5L A25A-FKS. The Camry Hybrid uses the A25A-FXS and a separate owner-manual section, while the available 3.5L V6 has a different capacity. A capacity printed beside the wrong engine code is not “close enough”; even engines sharing the same displacement can have different pans, filters, coolers, or drain-back behavior. If the vehicle has been swapped, rebuilt, or fitted with an aftermarket pan, use the installed hardware manufacturer's capacity and calibration marks.
The most common current application begins near 4.8 US qt. Begin below that amount and finish by measurement. The difference between the add and full marks is often about one quart, but do not assume that relationship when the dipstick is aftermarket, damaged, or paired with a non-original tube. Investigate a reading that remains absent or implausibly high.
Toyota describes the figure as a drain-and-refill reference. Add below 4.8 qt initially, run the engine long enough to fill the filter, inspect the drain plug and filter, switch off, wait more than five minutes on level ground and bring the dipstick level into range. The gasoline A25A-FKS page specifies SAE 0W-16; if 0W-20 is used only because 0W-16 is unavailable, Toyota directs replacement with 0W-16 at the next change.
Common causes of a capacity mismatch
Toyota describes the figure as a drain-and-refill reference. Add below 4.8 qt initially, run the engine long enough to fill the filter, inspect the drain plug and filter, switch off, wait more than five minutes on level ground and bring the dipstick level into range. The gasoline A25A-FKS page specifies SAE 0W-16; if 0W-20 is used only because 0W-16 is unavailable, Toyota directs replacement with 0W-16 at the next change. If the verified dipstick result and the expected quantity disagree materially, stop and identify the cause instead of choosing whichever number is more convenient.
- The lookup used the model name but not the model year or engine code.
- The quoted figure excluded the filter while the filter was replaced.
- The vehicle was not level or the oil had not drained back before checking.
- An oil cooler, remote filter, aftermarket pan, engine swap, or incorrect dipstick changed the system.
- The old filter gasket remained on the housing or a leak began after startup.
- The crankcase was filled to the advertised capacity without a final dipstick check.
Toyota 2018 Camry 2.5L specifications can change by model year, engine, platform, wheel, and installed component. Confirm the VIN or engine identity, part numbers, fastener condition, and the current manufacturer instructions before service.
Procedures used with this specification
These steps are the same for every vehicle in this family, so they are documented once rather than repeated on each page. The values above remain specific to this Toyota 2018 Camry 2.5L.
2018 Toyota Camry 2.5 Oil Capacity FAQs
How much oil does the 2018 Camry 2.5L take?+
Toyota lists 4.8 US qt (4.5 L) with a new filter for the gasoline 2018 Camry 2.5L A25A-FKS. Confirm the year/engine row and finish by the dipstick rather than treating the capacity as an exact pour-in amount.
Technical sources
TorqueSheet favors engine- and component-specific manufacturer instructions over unsourced universal values.
12018 Toyota Camry Owner's Manual — maintenance dataPrimary Toyota manual listing 4.8 qt (4.5 L) with filter for the gasoline A25A-FKS and distinguishing the Camry Hybrid manual.↗